Matt Water Based Epoxy Floor Paint

7. INSTRUCTIONS FOR USE

7.1. PREPARATION

THE PERFORMANCE OF THE COATING CAN BE SERIOUSLY IMPAIRED IF THE FOLLOWING INSTRUCTIONS ARE NOT STRICTLY ADHERED TO

Do not apply in temperatures below 10 °C/50 °F and ensure there is at least a 4 hour weather window. We do not recommend application late in the day, due to dropping temperatures and increased humidity.

Water Based Epoxy Floor Paint can be applied in mildly damp conditions but will not tolerate standing water.

Although Water Based Epoxy& Floor Paint& will overcoat most other finishes and paints, the best results are achieved when surfaces are clean and free of other finishes/coatings. If applying over an existing coating or to a non-porous surface, mechanically sand the area to create a key.

All surfaces should be dry, mildly damp or at least not subject to running water. Particular attention should be made to degreasing surfaces before application. All voids and surface imperfections must be carefully filled.

Clean the surface you will be applying the Water Based Epoxy& Floor Paint& to. If there are any leaks, these should be repaired with Antel Waterstop or Antel Epoxy Putty before applying the Water Based Epoxy Coating. If unsure, please contact us for technical advice.

The pot life is approximately 1.5 hours.  This is based on a temperature of 20 °C/68 °F.  If you are applying the coating in higher temperatures, the pot life may be reduced.  The material will become unworkable once outside of this pot life.

Once mixed, it is only possible to apply a single coat.  Do not attempt to return to the mix to apply a second coat.


7.2. MIXING

For simplicity we would recommend using a separate pack of Water Based Epoxy Floor Paint for each coat, however if you would like to use one pack for both coats, you will need to accurately divide the A and B packs proportionately using digital scales.

1. Mix the A Pack thoroughly.

2. Mix the B Pack thoroughly.

3. Pour the contents of the B Pack into the larger A Pack.

4. Mix again thoroughly (ideally with a mixer paddle) for a minimum of three minutes, so that the two components are completely mixed. 

5. Pour into at least one roller tray to maintain pot life.

6. Start application immediately.



7.3. APPLICATION STEPS

1. Apply the first coat by medium pile roller or brush.

2. Wait 24 hours before applying the second coat. Reduced time between coats maybe possible, but it’s very important to seek technical advice from Antel before attempting this.

3. Within a maximum period of 48 hours, apply the second coat.



8. CURING

Tack Free full Cure
at 20°C 65% RH 8 hours 3 days
at 8°C, 65% RH 24 hours 7 days
Pot life at 20°C 1.5 hours
Pot life at 10°C 2.5 hours

9. CLEANING TOOLS

Clean tools immediately after use with clean water

10. TYPICAL PERFORMANCE PROPERTIES

Taber abrasion Index (Mg) 20 per 1000 cycles.
Chemical Resistance:
Resistant to most dilute alkali systems e.g. 10% Sodium Hydroxide but has limited resistance to acidic attack e.g. Hydrochloric Acid.
Resistance to vehicular traffic - Good. Resistance to pedestrian traffic - Excellent.

TYPICAL PERFORMANCE PROPERTIES

Taber abrasion Index (Mg) 20 per 1000 cycles.
Chemical Resistance:
Resistant to most dilute alkali systems e.g. 10% Sodium Hydroxide but has limited resistance to acidic attack e.g. Hydrochloric Acid.
Resistance to vehicular traffic - Good. Resistance to pedestrian traffic - Excellent.

SHELF LIFE

12 months in sealed container.

24-48 Hour Dispatch

We pride ourselves on fast and reliable delivery. Most orders are dispatched promptly and typically arrive within 24-48 hours, subject to stock availability and courier schedules.

If there are ever any unexpected delays, our team will keep you informed as soon as possible.

For larger or ongoing projects where additional quantities may be required later, we recommend contacting us in advance so our team can help check current stock availability and product continuity for your project.