Wall Coating System 10 - Waterproof Wall Paint

Surface Preparation

Wall Coating System 10 can be applied over most existing paints and coatings, although the best results are achieved when surfaces are clean and free from previous finishes. All surfaces should be damp dry and free from running or standing water. Particular attention should be paid to removing grease and other contaminants before application.

Mixing

The performance of the coating can be seriously impaired if these instructions are not followed correctly.

1. Stir the contents of the larger container.
2. Pour the entire contents of the smaller container into the larger container, ensuring as much material as possible is scraped out.
3. Mix thoroughly using a mechanical mixer for a minimum of 3 minutes.
4. Continue mixing for a further 2-3 minutes to ensure complete dispersion of both components.

Pot Life

As a two-part epoxy system, Wall Coating System 10 has a limited working time once mixed. The pot life is approximately 1.5 hours at 20°C. Higher temperatures will reduce the available working time.

Application

Do not apply below 10°C (50°F) and ensure a minimum 4-hour dry weather window.

Wall Coating System 10 can be applied to mildly damp surfaces but must not be applied to standing water.

For simplicity, we recommend using a separate pack for each coat. If using a single pack for both coats, the resin and hardener must be divided equally and mixed separately for each coat. We recommend measuring by volume using a measuring jug to ensure accuracy.

Application Steps
1. Clean and prepare the surface before application. Any leaks or defects should be repaired using Antel Waterstop, Antel Epoxy Putty or Antel SBR Bonding Agent. If you are unsure, please contact us for technical advice.
2. Mix both components thoroughly according to the instructions above.
3. Apply the first coat by brush, roller or spray.
4. At temperatures above 20°C, allow approximately 6 hours before applying the second coat. At temperatures below 20°C, allow 24 hours before recoating.
5. Apply the second coat.

For detailed instructions and safety information, please refer to the product data sheet.

Packaging

A two part product available in 1, 2.5 and 5 litres. Non-returnable containers.

Storage

Store in a cool, dry and frost free area in original containers. Protect from freezing. Keep out of the reach of children. A shelf life in excess of 12 months can be expected for unopened containers kept in the above conditions.

Drying & Curing

At 20 degrees C and with reasonable ventilation, the coating is touch dry in 6 hours and hard dry in 12 hours. Maximum cure, hardness and chemical resistance is obtained within 7 days.

Coverage

Every litre of Wall Coating System 10 will cover approximately 6-7 squared metres (based on a non porous, smooth surface), however this will vary depending on how thickly you apply the material and also how porous the surface is.

If you are unsure on the porosity of the surface, we recommend you buy a little more than you think you will need to ensure you don’t run out part way through the application.

Cleaning Equipment

When using spray equipment a thorough rinsing with cold water every hour will prevent a build up of cured material. Brushes and rollers should be washed with cold water and detergent and rinsed thoroughly in cold water.

Health & Safety

Wall Coating System 10 is much safer to handle than other resin systems, however, it is recommended that all skin contact is avoided and that any areas of contact are washed immediately with soap and warm water. It is advisable to use a barrier cream and gloves when applying.

FOR FULL DETAILS PLEASE REFER TO HEALTH & SAFETY DATA SHEET.

For detailed instructions and safety information, please refer to the product data sheet.

24-48 Hour Dispatch

We pride ourselves on fast and reliable delivery. Most orders are dispatched promptly and typically arrive within 24-48 hours, subject to stock availability and courier schedules.

If there are ever any unexpected delays, our team will keep you informed as soon as possible.

For larger or ongoing projects where additional quantities may be required later, we recommend contacting us in advance so our team can help check current stock availability and product continuity for your project.