Epoxy Flake Flooring System

Antel Epoxy Flake Flooring System is a three-part system, consisting of one coat of base epoxy resin, PVA flake, and a top sealer coat to protect the underlying flake while adding increased gloss, chalk resistance, and chemical resistance.

Uses
The scope of applications for Antel Epoxy Flake Flooring System is extensive, and it can be used virtually anywhere that requires an attractive, hard-wearing, anti-slip floor.

Packaging
Supplied as a ‘pack’:

5-6 m² pack

- 2.5 KG of Base Epoxy Resin (A & B Pack)
- 4 KG PVA Flake
- 1 KG of Sealer (A & B Pack)

10-12 m² pack

- 5 KG of Base Epoxy Resin (A & B Pack)
- 8 KG PVA Flake
- 2 KG of Sealer (A & B Pack)

Coverage
Depending on the substrate, coverage is approximately 5-6 square metres per pack on a non-porous, relatively smooth surface. On rougher and more porous surfaces, the coverage of the Base Epoxy Resin may be reduced.

Preparation
THE PERFORMANCE OF THE COATING CAN BE SERIOUSLY IMPAIRED IF THE FOLLOWING INSTRUCTIONS ARE NOT STRICTLY ADHERED TO

- Do not apply in temperatures below 10°C/50°F.

- Although the Epoxy Flake Flooring System will overcoat most other finishes and paints, the best results are achieved when surfaces are clean and free of other finishes/coatings.

- If applying over an existing coating or to a non-porous surface, mechanically sand the area to create a key.

- If applying to a surface that hasn’t previously been painted or is porous, one coat of Epoxy Solvent Free Primer must be applied before the Epoxy Flake Flooring System.

- All surfaces should be dry. Particular attention should be given to degreasing surfaces before application. All voids and surface imperfections must be carefully filled.

- Epoxy Flake Flooring System can be applied to fibreglass, but the surface must be mechanically sanded to provide a key.

- If there are any leaks, repair them with Antel Waterstop or Antel Epoxy Putty before application.

- The pot life of the Base Coat and Sealer Coat is approximately 45 minutes at 20°C/68°F. Higher temperatures may reduce this time.

- We recommend wearing spiked shoes when applying the Flake.

If unsure, please contact us for technical advice.

Application
1. Mix the Base Epoxy Resin A Pack thoroughly on a slow speed.
2. Mix the Base Epoxy Resin B Pack thoroughly on a slow speed.
3. Pour the contents of the B Pack into the larger A Pack.
4. Mix again thoroughly on a slow speed (ideally with a mixer paddle) for at least three minutes, ensuring complete mixing.
5. Pour into at least one roller tray to maintain pot life.
6. Apply the Base Epoxy Resin using a medium pile roller or brush.
7. While wearing spiked shoes, broadcast PVA flake as evenly as possible over the area. A tyrolean/flicker gun will make this much easier.
8. Wait 12-24 hours.
9. Vacuum off excess flake.
10. Mix the Sealer Coat A Pack thoroughly.
11. Mix the Sealer Coat B Pack thoroughly.
12. Pour the contents of the B Pack into the larger A Pack.
13. Apply the Sealer Coat using a foam roller.

Drying & Curing
At 20°C, and with reasonable ventilation:

The coating is touch dry in 8 hours and hard dry in 12 hours.
Maximum cure, hardness, and chemical resistance are obtained within 7 days.

Light traffic is recommended after 1-2 days.
Heavy traffic is recommended after 4-5 days.

This is a guide only and will depend on temperature and the thickness of the Sealer Coat applied.

Storage
Store in a cool, dry, and frost-free area in original containers. Protect from freezing. Keep out of the reach of children. Unopened containers can be expected to have a shelf life of over 12 months if stored correctly.

Cleaning Equipment
Application equipment should not be cleaned with water. Instead, allow it to cure/harden and then dispose of it.

Health & Safety
Antel Epoxy Flake Flooring System is much safer to handle than other resin systems; however, all skin contact should be avoided. If contact occurs, wash immediately with soap and warm water. Use a barrier cream and gloves when applying.

FOR FULL DETAILS, PLEASE REFER TO THE HEALTH & SAFETY DATA SHEET.

A Note from Antel
We make every attempt to provide as much information as possible on the mixing and application of Antel’s Epoxy Flake Flooring System. However, if you have any questions or a specific request, please contact us—we are happy to help. Antel is committed to providing excellent before and after-sales service.

Test Data @20°C (Sealer Coat)

Pot life: 45 minutes
Touch dry: 8 - 10 hours
Foot traffic: 24-48 hours
Full Cure: 3 – 7 days
Application Thickness: 70 microns per coat
Ideal application temperature: 15-20°C
Finish: Gloss
% solids W/W: 68
Viscosity @20°C spindle 3 20rpm: 9.0 Pa.s
Specific Gravity @ 20°C: 1.4
Maximum humidity for application: 80%

Speedy delivery is our promise! Expect your order to arrive promptly, typically between 24-48 hours, thanks to our efficient service.