Epoxy Self-Levelling Floor Screed

Preparation: Surfaces must be dry and free from all foreign matter such as dust, grease and dirt etc. Weak laitance and loose or flaking material must be removed by ‘grit’ blasting or at the very least wire brushing. Best results can be obtained by the use of the appropriate Antel cleaner.

Due to the porosity of substrates having an effect on the structure of self smoothing systems, it is important to apply a primer to the substrate in order to seal it. Antel’s Self Smoothing Floor Screed Primer has been especially developed for this purpose.

Mixing: Stir the B Pack. Empty the entire contents of A Pack 1, A Pack 2 & B Pack into the bucket (as supplied) and mix with drill and paddle for 3 minutes on a slow speed. Slowly add powder C Pack while mixing continuously. Finally, stir for a further 3 minutes to obtain a smooth free flowing mix. Pour immediately. Do not allow the aggregate to settle before pouring.

Application:
Once mixed Antel Self-Smoothing Floor Screed can generate a lot of heat. Storing the material in a cool place and applying in cooler conditions will reduce the amount of heat generated and result in the best possible finish.

Having allowed two coats of Antel Self Smoothing Floor Primer to cure, pour the compound on to the substrate and spread out using a squeegee/float before using a ‘spiked’ roller, which not only aids movement of the compound but aids de-aeration also. Apply at a thickness of 2 mm.

IMPORTANT - We strongly recommend wearing spiked shoes so that a spiked roller can be used across the entire area while still wet. Failure to do this may result in a subpar finish.

Curing:
Pot life 160g mix @ 25°C = 25 minutes
Thin film set time @ 25°C = 7 hours
@ 10°C = 23 hours
Full cure schedule 2 - 7 days at ambient temperature.

Overcoating: Further protection can be obtained by using one of a selection of Antel floor paints.

Cleaning tools: Immediately after use, tools should be cleaned with Antel cleaning solvent.

Packaging

Four pack system consisting of “A1”, “A2”, “B” and “C” (resin, hardener powder).

Available in:

10kg
25kg


Colour
Available in a wide range of colours.

Colours can be custom mixed to order, allowing you to match your project requirements.

Please note:

Custom-mixed colours cannot be returned once supplied

This product is not fully UV stable, so some colour change may occur over time, particularly in lighter shades or areas exposed to direct sunlight

UV Stability
- This product is not fully UV stable.
- Discolouration may occur over time, particularly in lighter colours or areas exposed to direct sunlight.

Coverage
25kg covers approximately 6–7m² at 2mm thickness

Recommended Thickness
Typically applied at 2mm

Shelf Life
12 months in sealed containers

Curing:
Pot life 160g mix @ 25°C = 25 minutes
Thin film set time @ 25°C = 7 hours
@ 10°C = 23 hours
Full cure schedule 2 - 7 days at ambient temperature.

Overcoating: Further protection can be obtained by using one of a selection of Antel floor paints.

Cleaning tools: Immediately after use, tools should be cleaned with Antel cleaning solvent.

TYPICAL PERFORMANCE PROPERTIES
After 7 day cure @ 25°C
Flexural strength, Mpa -40
Flexural Modulas, Gpa -6
*Chemical resistance (data available) -very good
Water spotting resistance -excellent
Colour stability - long term
* NOTE: Chemical resistance is specific, therefore seek advice

24-48 Hour Dispatch

We pride ourselves on fast and reliable delivery. Most orders are dispatched promptly and typically arrive within 24-48 hours, subject to stock availability and courier schedules.

If there are ever any unexpected delays, our team will keep you informed as soon as possible.

For larger or ongoing projects where additional quantities may be required later, we recommend contacting us in advance so our team can help check current stock availability and product continuity for your project.