Dairy Coat Anti-Bacterial has been further enhanced by the addition of a highly effective anti-microbial agent that has a 99.999% kill rate against E. Coli and MRSA.
The additive contained will not leach and has no environmental impact.
It is effectiveness is unaffected by:
Scratching or abrasion
UV exposure
Salt Spay
Temperature cycling
Cleaning chemicals including Chlorine Bleach, Disinfectants, Quaternary Ammonium Compounds.
Effective for the life time of the coating.
The active ingredient is effective against most bacteria including Listeria, Monocytogenes, Salmonella Enteritidis, Pseudomonas Aeruginosa and Aspergillus, Niger and specifically tested against MRSA and E. Coli.
No document evidence that bacteria strains have become resistant.
Epoxy Application Kit - £21.99
Floor Paint Application Kit -...
Dairy Coat Antibacterial Technical Data Sheet
1. DESCRIPTION
Antel Dairy Coat is a universal water based epoxy resin coating designed for easy and safe application. Dairy Coat possesses most of the properties of conventional epoxy resins with many additional advantages, particularly its tolerance of damp application conditions. It is applied in the same manner as ordinary emulsion paint and dries quickly to form a tough, easily cleaned coating, providing a vapour barrier. The coating is non toxic, resistant to oil, and most mild chemicals. Subsequent over coating can be carried out after the original surface has been thoroughly degreased and cleaned.
2. USES
The scope of applications for Dairy Coat is extensive and it can be used virtually anywhere that concrete or masonry requires protection or waterproofing.
Recommended areas and types of use :-
1. Wall coating in areas of food manufacture and storage.
2. Tank lining for protection against mild chemicals.
3. Waterproofing and decorative finish for all brick, concrete, cement, masonry and asbestos surfaces.
4. As a general weatherproofing and waterproofing coating.
5. For application to damp surfaces where other paints cannot adhere.
6. As a membrane to prevent rising damp in floors.
7. As a sealing coat for materials containing asbestos.
8. Sealing wet rooms.
Typical locations :-
1. Water tanks/sewage treatment plants.
2. Abattoirs.
3. Dairies/milking parlours, food factories, breweries.
4. Grain silos.
5. Basement/damp proof membrane.
6. Chemical industry garages.
7. Bunds and water plants.
8. Wet rooms.
3. PACKAGING
A two part product available in 1, 2.5 and 5 litres. Non-returnable containers.
4. STORAGE
Store in a cool, dry and frost free area in original containers. Protect from freezing. Keep out of the reach of children. A shelf life in excess of 12 months can be expected for unopened containers kept in the above conditions.
5. DRYING & CURING
At 20 degrees C/68 degrees Fahrenheit, and with reasonable ventilation, the coating is touch dry in 6 hours and hard dry in 12 hours. Maximum cure, hardness and chemical resistance is obtained within 7 days.
6. COVERAGE
Each litre of Dairy Coat will cover approximately 6-7 squared metres (based on a non porous, smooth surface), however this will vary depending on how thickly you apply the material and also how porous the surface is.
If you are unsure on the porosity of the surface, we recommend you buy a little more than you think you will need to ensure you don't run out part way through the application.
7. CLEANING EQUIPMENT
When using spray equipment a thorough rinsing with cold water every hour will prevent a build up of cured material. Brushes and rollers should be washed with cold water and detergent and rinsed thoroughly in cold water.
8. INSTRUCTIONS FOR USE
8.1. PREPARATION
THE PERFORMANCE OF THE COATING CAN BE SERIOUSLY IMPAIRED IF THE FOLLOWING INSTRUCTIONS ARE NOT STRICTLY ADHERED TO
Do not apply in temperatures below 10 °C/50 °F and ensure there is at least a 4 hour weather window. We do not recommend application late in the day, due to dropping temperatures and increased humidity.
Dairy Coat can be applied in mildly damp conditions but will not tolerate standing water.
Although Dairy Coat will overcoat most other finishes and paints, the best results are achieved when surfaces are clean and free of other finishes/coatings. If applying over an existing coating or to a non-porous surface, mechanically sand the area to create a key.
All surfaces should be dry, mildly damp or at least not subject to running water. Particular attention should be made to degreasing surfaces before application. All voids and surface imperfections must be carefully filled.
Clean the surface you will be applying the Dairy Coat to. If there are any leaks, these should be repaired with Antel Waterstop or Antel Epoxy Putty before applying the Dairy Coat. If unsure, please contact us for technical advice.
The pot life is approximately 1.5 hours. This is based on a temperature of 20 °C/68 °F. If you are applying the coating in higher temperatures, the pot life may be reduced. The material will become unworkable once outside of this pot life.
Once mixed, it is only possible to apply a single coat. Do not attempt to return to the mix to apply a second coat.
8.2. MIXING
For simplicity we would recommend using a separate pack of Dairy Coat for each coat, however if you would like to use one pack for both coats, you will need to accurately divide the A and B packs proportionately using digital scales.
1. Mix the A Pack thoroughly.
2. Mix the B Pack thoroughly.
3. Pour the contents of the B Pack into the larger A Pack.
4. Mix again thoroughly (ideally with a mixer paddle) for a minimum of three minutes, so that the two components are completely mixed.
5. Pour into at least one roller tray to maintain pot life.
6. Start application immediately.
8.3. APPLICATION STEPS
1. Apply the first coat by medium pile roller or brush.
2. Wait 24 hours before applying the second coat. Reduced time between coats maybe possible, but it’s very important to seek technical advice from Antel before attempting this.
3. Within a maximum period of 48 hours, apply the second coat.
9. HEALTH & SAFETY
Dairy Coat is much safer to handle than other resin systems; however, it is recommended that all skin contact is avoided and that any areas of contact are washed immediately with soap and warm water. It is advisable to use a barrier cream and gloves when applying.
FOR FULL DETAILS PLEASE REFER TO HEALTH & SAFETY DATA SHEET.
NOTE REF 1
Antel Dairy Coat – Clear
With the formulation of the emulsion the mixture will take on a milky colour. This milkiness will gradually disappear during the curing cycle provided that the coating is not too thickly applied nor allowed to fill holes in the surface area of the application. If either of these situations does occur the milkiness will not disappear. All voids or surface imperfections must be carefully filled prior to any application of Clear Dairy Coat.
Antel Dairy Coat is available in a variety of colours. Please enquire for details.
Swimming Pool Paint
A1 Pond Paint
Epoxy Coating (Water Based)
Epoxy Coating Heavy Duty (Solvent Free)
Epoxy Coating Matt (Water Based)
Epoxy Self-Smoothing Floor Screed
Epoxy Garage Floor Paint Kit
Tanking Slurry
Epoxy Putty
Epoxy ClearCoat Resin
Contact Adhesive
Contact Adhesive Cleaner
Non Flammable Contact Adhesive
Resin Wood Adhesive Oneshot
Epoxy Application Kit
Floor Paint Application Kit
Pond Paint Application Kit
Pool Paint Application Kit
Pond Paint Application Brush
Tanking Slurry Application Brush
Spiked Roller
Spiked Shoes
12" Medium Pile Roller
Trowel
Squeegee
400ml Empty Cartridge
A1 Pond Paint
Epoxy Putty
Rendermix
SBR Waterproof Bonding Agent
Swimming Pool Paint
Tanking Slurry
Wall Coating System 10
Dairy Coat Antibacterial
Dairy Coat Ultra Antibacterial
Epoxy Floor Screed
Feed Passage Epoxy Coating
Epoxy Bagging Coat
Kennel & Cattery Paint
Epoxy Floor Paint Heavy Duty (Solvent Free)
Epoxy Floor Paint (Water Based)
Epoxy Floor Paint Matt
Epoxy Floor Paint Primer
Epoxy Self-Smoothing Floor Screed
Epoxy ClearCoat Resin
Epoxy Garage Floor Paint Kit
Epoxy Chemically Resistant Coating Solvent Free
Epoxy Primer (Solvent Free)
Epoxy Flake Flooring System
Epoxy Quartz Flooring System
Epoxy Line Paint
Epoxy Glaze Coat
Anti-Slip
Epoxy Cleaning Solvent
Epoxy Floor Screed
Epoxy Mortar
Epoxy Road Surface Bedding Compound
Suredeck Flooring System
Suredeck Flooring Sealer
Suredeck Flooring Primer
Suredeck Flooring Quartz
Epoxy Grout Aggregate Filled - Winter Grade
Fast Set Epoxy Line Paint
Epoxy Primer Fast Set
Epoxy Primer Fast Set Plus
Fast Set Grip Coat
Fast Set Epoxy Solvent Free Coating
Epoxy Adhesive Sealer
Epoxy Cleaning Solvent Free
Epoxy Glaze Coat
Epoxy Grout Adhesive
Epoxy Grout Aggregate Filled
Epoxy Grout Liquid
Epoxy Grout Thixotropic
Low Viscosity Grout
Aqueous DPC Concentrate
DPC Injection Cream
DPC Microjet
Passive Vent
Rendermix
SBR Waterproof Bonding Agent
Waterbased Epoxy Coating
Epoxy Coating Matt (Water Based)
Waterproofer
Waterstop