Epoxy Putty Rapid View larger

Epoxy Putty Rapid

New

Antel Epoxy Putty Rapid  is a two part epoxy resin material with excellent adhesion to most building materials - wet or dry - even under water.  It has very good chemical resistance coupled with excellent bond strength. Although outwardly rigid Epoxy Putty will accommodate approximately 5% tension and flexure. Once mixed, it will cure in 30 minutes and is then ready to sand.

More details

£ 47.74

Volume discounts

Quantity Price You Save
8 £ 42.01 Up to £ 45.83
5 £ 42.97 Up to £ 23.87
3 £ 43.92 Up to £ 11.46
2 £ 45.35 Up to £ 4.77
1.  Description 

Antel Epoxy Putty Rapid  is a two part epoxy resin material with excellent adhesion to most building materials - wet or dry - even under water.  It has very good chemical resistance coupled with excellent bond strength. Although outwardly rigid Epoxy Putty will accommodate approximately 5% tension and flexure. Once mixed, it will cure in 30 minutes and is then ready to sand.

2.  USES

Used to seal a wide variety of vertical and horizontal joints in such situations as:-

- Swimming pools and other water retaining structures.

- Water tanks/sewerage treatment plants
- Food processing plants.

Joints in concrete and earthenware pipes can now be effectively sealed.  Ideal for sealing joints in acid resistant floor tiles where chemical resistance is required.  As a putty type adhesive for most materials found in the construction industry.

3.  PACKAGING    

Epoxy Putty is supplied in two parts. Pack A and Pack B making a total of 1 litre mixed material.

Non returnable containers.

4.  COLOUR           

Rapid Grade - WHITE

5.  USAGE RATE

1 litre will seal 7 linear metres in a joint section 12 mm wide by 12 mm deep. Please refer to the table on the following page for further coverage details.

 

6.  SHELF LIFE/STORAGE

Epoxy Putty Rapid has a shelf life of 12 months if kept in the original SEALED CONTAINERS. Keep in cool, dry frost free conditions in original sealed containers. Protect from freezing. Keep out of the reach of children.

 

7.  HEALTH & SAFETY  

This product contains epoxy resin and hardeners which are known to cause skin irritation to some people.  Wear protective clothing and wash well on completion of each work session. 

Should the putty come into contact with the skin it must be washed off promptly.  If in contact with the eyes flush with cold water for at least 15 minutes and seek medical attention.  Users are recommended to use barrier cream.

PLEASE REFER TO SAFETY DATA SHEET FOR COMPLETE INFORMATION

8.  INSTRUCTIONS FOR USE

8.1 preparation

Surfaces must be free of all loose and flaking paint, dust, dirt, laitance or grease.  It is most important that surfaces are properly prepared.

8.2 mixing

Take equal quantities from Packs A and B and mix together thoroughly until a completely uniform colour is obtained without streaks.  Mixing is best carried out by hand.  Wear gloves.  Do not mix more material than can be used within 5- 10 minutes.

8.3 application

Immediately after mixing, press the Epoxy Putty into the joint sides with a trowel or palette knife to obtain maximum contact. A smooth finish can be achieved by tooling with a knife dipped in solvent.  The material will not slump in joints up to 20mm wide by 20mm deep.  Joints to be sealed should not be less than 6mm wide by 5 mm deep.

8.4 curing

The pot life when mixed is 5 – 10 minutes

Initial cure is achieved in 30 minutes.

Full cure is achieved 2 - hours dependent upon the temperature.  The lower the temperature the longer the cure time.

Do not use at temperatures below 4 degrees C.

8.5 tool cleaning

Tools can generally be cleaned in solvent provided they have not been allowed to dry. 

6 other products

Special Offers

Viewed products

PayPal